Wednesday, January 6, 2016

Solar panel power

Finally set up a solar panel to re-charge the 12v battery. Also get Teria "off-grid" and gain a new level of freedom.

The 35 watt solar panel once powered-up my Endeavor 24 sloop for about 6 months in the late 1980s. Since then it has lived in various sheds etc for 27 years, so fingers crossed that it still can pump-out enough power. It was made by BP solar  in 1987. I can't remember the exact power specs but a modern 35W panel has a maximum output of just under 18 volts @ 2 amps

35W solar panel on deck during set-up testing

Connected some heavy duty 12v wires to the battery terminals and the other ends went to the regulator box.

Solar power wires (in white casing) connected (yellow) to battery terminals


Installed a 20 amp 12v solar regulator in the fuse/storage box. They need to be in a fairly dry spot less than 1m from the battery. It also needs to be easily visible.

End connectors were crimped onto the ends of the panel wires and ends of the battery wires, keeping with black negative and red positive.

It should control power input into the battery, shut down the power if the battery charge is full so it won't overcharge. This should stop battery damage and let the battery live a long healthy life.

The red LED fired up immediately - like a small sun in the middle of the word "solar",,it indicates that the battery is charging from the panel but is not at full charge yet.

LED red - battery charging up
Found that these 20A regulators are still available at Jaycar electronics . 20A may be allot but it allows for system expansion and will be not working too hard.

Tidied up the system. Siliconed the regulator onto the bulkhead inside the locker. Cable-tied the battery wire out of the way. 

On the panel cable tied the power cable to the panel frame to stop it pulling on the black box underneath (could be a diode to stop back flow current).

Added 4 lengths of 4mm braided cord line to the corners of the panel - for attaching it it various things around the boat. Idea is to keep the panel mobile. So it can be best positioned to catch the maximum amount of sunlight, or be stowed below when rough sailing. For now i put it on top of the lowered mast tied to the spreaders.

Solar panel position with mast lowered.


The red LED light turned off at dusk. indicates the regulator has switched off the solar input wires.

12V electrical tools, materials on the "workbench"
Next morning around 10am found the LED was green indicating a full battery charge (14.4v) . I put the panel inside then the LED went red again (charges up from about 13v). So put the panel out -tied onto the aft rail quarter. The LED went orange then yellow to indicate charge was nearly at peak.

LED going orange..

LED going yellow..nearly full charge

LED Green  - full charge
The regulator has an intermittent charging cycle - every 20 minutes it disconnects from the solar array for a few minutes. This is good for deep cycle battery lifespan (hopefully this 60 Amp Hour heavy duty battery too).

The solar regulator is doing this




Dry location in the fuse/stowage locker

Louvred door

So far it looks like the system can  keep the battery topped up when no electrics are turned on in the boat. Hope it can stay on top of it when sailing.

With luck the system is good enough and it's the end of the "grid-connected" era.  Teria's potential range has been further extended.









Sunday, January 3, 2016

Teria summer (wet season) maintenance

Did some maintenance/ additions to Teria during our "Summer" (tropical wet-season) holidays to get seaworthy again (not much sailing as it's too hot-humid with chance of thunderstorms/lightning strikes offshore at times)

1) Re-sealing and re-riveting the portholes The original aluminium rivets were breaking off and the port hole frames were springing out causing leaks. The last sail in heavy weather and some heavy rains recently provided the motivation (chart soaked twice!). The starboard cabin porthole had lost over 50% of its rivets and was nearly ready to pop out for good. The port sides 2 portholes had about a 30% rivet failure rate.

So drilled the bad old rivets out, and enlarged the holes a little, scraped old silicone etc out, applied new silicone and put the new slightly larger diameter aluminium rivets in. I left the original white rubber sealant tape under the window flanges. The black inner rubber strip of the forward port porthole was a bit aged, some shrinkage etc causing pull away from corners, so pulled it out and rebedded it..the 1" ends gap (due to shortening) was filled with silicone sealant.  All rivet heads-holes were also silicone sealed too.

starboard

port side

black inner rubber strip

rivet tool


2) The sloppy tiller to rudder join - Glued a wooded block onto the tiller side. Next day planned the block down to fit the rudder stock head socket. No more tiller slop.

clamped block

tiller fitting

3) Engine department
The outboard had some running problems last trip - probably the most critical item on the boat.
Replaced 2 spark plugs and oiled greased all external moving bits  around the top of outboard.
Engine test went well. Really don't want to get stranded out there in a calm (or storm).

Engine test stand - trampoline frame and paver
Checked the u/s fuel tank gauge mechanism,  Pulled it out, the indicator pointer part missing and sight glass clouded over and leaking a bit. (the float and control wire still ok). The petrol intake still good so still using it as is.

4) Mast crutch (shear legs). Made from 2nd hand 12x50mm (1.2x2") hardwood planks about 6 ft long with a pivot bolt allowing scissor-action for stowage. This frame holds the lowered mast up giving standing headroom in the cockpit. Good for river with low bridge motoring (rudder remains in operation). The shade/rain awning can also be added to create a cool/dry cockpit area.  Rounded off some sharp corners with the surform plane  and sanded it down. It's a prototype in progress.

The design problems with it at this stage -
    It can't be used as a mast-raising aid (would fall over)
    The cockpit locker hatches can't fully open, they hit on the wood frame..
    It's too heavy - lighter material better.



5) Short-link anchor chain - Bought 18m of 6mm short-link galvanized chain at Bullivants, Townsville, they are a construction-rigging supply company. ($5/m) It is rated to 400kg safe working load (but can take at least twice that). Plus two 6mm bow shackles rated to 500kg SWL . Fit the new chain between the 7m of 6mm long link chain and the 12mm rope warp to give Teria a total of 25m of chain. With 100% chain between anchor and sampson post there's almost no chance of  it chafing through during the night. Plan is to use it in shallow anchorages, especially the nearby islands. Peace of mind when leaving the boat alone or sleeping aboard.  Just hope it's not too much weight up high in the bow, or weight to haul up by hand.

Short-link seems to handle and stow easier too.

short link chain and rope warp

long link chain and 10 lb anchor on deck (all fits in locker)
Kept the rope warp so there is deep anchoring capability (20-25m depths such as between coast and barrier reef). It could be handy if the boat is disabled offshore, stop it drifting away.

6) Stern light - The old white stern navigation light was cracking, leaking, gaffer-taped up and very unreliable, it often went off when needed at night. Thought about buying a new LED one but  ended up replacing the old stern light with an unused stern light that i had laying around. It was  a 10amp old bulb style but this one is still in top condition and is reliable.

Saturday, January 2, 2016

Fatty knees - Boxing day sail (rudder test)

Dec 26 th 2015, "boxing day" in Australia which is better known for the start of
the Sydney - Hobart yacht race. The super yachts headed south

Far to the north, a Fatty Knees 8' dinghy quietly took to the sea again. It was sail #30 , to test the restored rudder and try sailing JaiDee from Ross Creek in Townsville city centre for the first time.

It was the last day of a good weather window for Townsville  so everything was prepared by 4pm and the ute headed for the ramp with dinghy in tow. Ross Creek boat ramp (photos, map,etc - Fishing Townsville . It's also known as "Coast guard ramp")  (Forecast over next days for monsoonal rains associated with a cyclonic low in the NT, so last chance to sail for awhile)

Townsville city was initially built on the banks of Ross creek in the 1870s-1880s. The narrow inner harbour has a yacht club and marina, Passenger ferries, Car ferries and some marine maintenance facilities. Most moored vessels are in 24 - 120 foot range. The modern outer commercial shipping harbour is a large basin.  Oil tankers and bulk-carriers can berth here. There is also a cruise ship terminal.

I was lucky even though it was a moderate wind day (13kn ENE) the ramp car park was almost empty, only a hand-full of large boat trailers there and a couple of runabouts were being hauled out.

Parked in the  "rigging up lane" next to the south (inner) ramp. Set up the rig with mast down and sail furled before launching. This was my first time to use the new floating pontoon beside the ramp.   It  makes solo launching much easier, safer and faster - a great improvement done by the city council.

Rowed at first as the wind was coming directly down the  narrow channel. Not much space to tack back and forth with 100 ft? passenger ferry cats also using the inner channel. Rowed past rock fishermen on the long break wall and waved g'day.  It was about a 300-500m haul before the shipping basin which had plenty more room to sail in.

Rigged up on the water as there was nothing to shelter behind or tie on to (hanging off a nav bouy wouldn't be very good form!). The centreboard down first to reduce drift rate, rudder shipped next - bit difficult to get the lower pintle aligned and in as it was underwater and choppy (so note to do it earlier in a calm place), the mast-sail was easy to step and the downhaul quickly belayed on the anchor cleat. A bit hard to steer while all this going on (so note to set up tiller lashings earlier too)


Tacked upwind just clear of the ferry channel, but not too far into the ship basin (wind shadows in there from ship and docks etc). It was long outbound starboard tacks and short across port tacks. Set up the tiller lashing rope - clove hitch on tiller , the loose ends through the quarter ring eyes and tied with sliding knots. Fatty knees can sail hands free upwind with tiller lashed. The slide knots are slid loose to steer by hand again.

Once clear of port and channel a port close haul was held to gain sea room , away from the duckponds rock wall which has some wave rebound and resultant confused sea. This hardly affects a Fatty knees it bobs over "rogue waves" or ships wakes like a cork. Heeling about 20 degrees gives a much higher windward free-board and only occasional bow spray blew aboard. The bilge sponge soon cleared it.

Sailed out a few km on a NW course, West point of magnetic Island on the bow. The tiller lashed allowed for thermos coffee break and dinner , at about 2-3 knots.



Hand steering gets the dinghy faster at 3-4 knots.

Checked the navigation system - a samsung Galaxy ace smartphone with Polaris navigation app. Inside a clear plastic waterproof neck pouch. The phones GPS gave the postion as lat/long, speed and compass heading on one page, the map page gives a position on a google earth map. Jai Dee was half way to magnetic Island with the middle reef navigation pylon in sight when it was time to turn back.

Nav & phone
The rudder was going very well. It felt much more reassuringly solid than the old kick-up rudder. Just the thing for bay sailing.

Fixed blade wooden rudder

The summer solstice was just a few days earlier so sunset was late for here at 6.45pm. Long grey clouds to the NW cut off most of the sunset, they were the outer extent of the large monsoonal system covering northern Australia. Set up the navigation lights on dusk.

Grey skies advancing from the NW
The harbour entrance is easier to sail into than Ross River. The main thing to watch out for is fast ferry cats and stay clear of the channel until time to enter. No tugs or ships were operating. Ran downwind on the calm port waters about 20-30m out from the break wall. The port of Townsville is a good sea-break and shelter to windward. The lead lights were bright white like laser beams when further out , then turned to all round blue when close to them. Green and red navigation channel buoys and poles lights flashed.

Ross creek dusk

Sailed on to the outer ramp. Hove-to there to wait and let the ferry cat pass out, (they sounded 3 horn blasts as they reversed out of berth). Then continued into the inner harbour. Yacht club marina to port. To Starboard was the ferry cat, reef cat berths, then aquarium, museum with old ship berth alongside.

The "sugar shaker" with its green "headband" light comes into view ahead on the final leg of the sail-able creek. Starboard in the Flinders st night club area, unusual to see it from this perspective. The low bridge stops further sailing up creek. So tied up at an all-tidal jetty with concrete stairs, stowed the sailing rig and converted to row-boat again.  The artificial sounds of amplified music from Palmer st cut the air like a knife and it was good to get going again.

The tidal current was still coming in as was the breeze, so rowing back was the only option. Sailing would've gone nowhere fast. Having and engineless craft make you  aware of every nuance in the tide and wind.  I stuck to the sides of creek with the least current first it was near the yacht marina berths on the east (south bank) side, then crossed to follow the north bank (Flinders st side) back to the ramp.

Tied up to the articulated pontoon. It was not far to the car and trailer from there so a quick solo retrieval onto the trailer.

Ross creek boat ramps new floating pontoon

Saturday, December 26, 2015

Original rudder restoration - Fatty Knees

The simplest and quickest way to get the rudder going again was to attach the rudder fittings to the original fixed rudder blade.

Removed the pintles and tiller fitting from the broken kick-up rudder. Then bolted these fittings onto the original fixed rudder blade. It was  a fortunate piece of spare gear that came with the dinghy sale. The original blade was beautifully crafted from a single piece of oregon pine or similar, faired nicely and varnished. The fittings had come off this blade once so they fitted on easily again (with a little bending of the tangs)

Original fixed rudder blade Fatty Knees dinghy

It certainly looks allot stronger than the kick-up rudder. It is definitely allot simpler. Only bad thing is it is a fixed blade with no kick-up function, hitting the bottom should never happen. It needs to be fitted in deep enough water and removed likewise. Some new techniques to devise and learn for getting away, returning and navigating shallow waters  - such as using an oar as a sweep in the transom notch.

Shipping the rudder, lower pintle first

Rudder shipped. Gudgeons and pintles detail.



Tiller fitting
Raised tiller position
Anyway the dinghy's seaworthy again and plenty of time gained to repair the broken kick-up rudder

Monday, December 14, 2015

Broken rudder on Fatty Knees

It was a nice 30C, 10-15kn ENE onshore breeze in early December so we took the Fatty Knees out for a sail.

1 ft waves were breaking and the wind was blowing straight onto the beach. This made getting under way a bit more difficult than usual. I had to walk the bow out past the shore break, get the centreboard half down, bear the bow away, sheet in a bit, jump aboard, sheet right in and close haul away.

When just clear of the break i put the rudder blade full down, hoping to sail clear ..but it was a bit too early, a breaking wave caught the bow and washed us shoreward, the rudder blade bashed down into the sandy bottom a few times so it had to be raised again in order to sail clear of the lee shore. Once clear it was lowered again as usual.

All was good for at least 15-20 minutes, we sailed out off Cape Palleranda into a confused lumpy sea which was due to two wave directions meeting up, they came from the north and east. Once clear of the cape we tacked and set course for Rowes Bay end of the beach to the south of us.

After a few minutes there was a bump, loud bang then the rudder blade broke. At first i wasn't sure what had happened, the tiller felt strange. I thought we hit something, but nothing to be seen. Not a log was it a turtle? We saw the lower 3/4 of the blade floating astern, i checked the rudder which still apparently had a blade hanging down. On seeing the damage it became clearer, the rudder blade had split in half down the centreline. It was made of plywood so de-lamination allowed it.

I pulled the half blade up , as in its weakened state it may break off completely. Then we couldn't steer the boat. We kept an eye on the half blade floating away, it drifted off 5 m, 10m, 15m..disappearing for longer and longer below wave crests. I wanted to retrieve it, for curiosity's sake and possible repair.

So we decided on using the oar to steer the boat. Out of it's stow bag in the bow then the two parts of the oar clipped together (like a tent pole). At first it was shipped into a side rowlock and rowed to get the bow to turn towards the "blade overboard". This wasn't too good so next was to put the oar into a small notch in the transom and use it as a sweep oar - a quick way to rig up a jury steering system. This worked and we headed back to pickup the half blade.

Sailing back was quick enough but it was far harder to steer than normal. I held the sweep against the rudder stock head with one hand and steered with the other. (to make a better job a rope lashing would have been better)

Anyway we sailed back about 1km on a beam reach to downwind run in a fairly safe manner.



On the beach a closer inspection of the damage revealed that the blade had cracked just where the aluminium clamp ended, then the plywood split along a centreline de-lamination. The design of the lower swivel clamp was an accident about to happen. It appears to be an after-market possibly home-made job, not the original rudder.

Monday, July 20, 2015

Heavier weather - 2nd day (trip #12)

Daybreak came and realised i was off the boat ramp when a tourist speed boat did many laps around Teria with kids gleefully screaming as they clung to a huge tyre device towed behind it. Managed to boil the water without tipping the trangia stove over on speedboat wakes and have some brekky.

Hauled on the Johnnos starter cord, many times, and to no avail..she was not starting (for the first time) and looked like it was flooded with fuel. So sailed off and anchored in amongst the 20 or so yachts further into the fairly calm and very well sheltered anchorage area. wind gusts were still over 15 knots at times tho.

Had a go fixing the outboard, it would be nigh impossible/ very dangerous to try to get home without it going in the current weather. Removed the spark plugs, fuel soaked and dirty, and did some rudimentary plug cleaning with my leatherman (note- bring good plug cleaning gear, &/or spare plugs) . It finally fired up on one cylinder after many attempts at plug removal and cleaning.

So set sail about 10am. Attempted to go back the way I'd come in around the windward eastern side of Island. Persevered  trying to tack upwind into 25 knots plus and short steep 2m plus seas upwind of a dangerous lee shore consisting of huge granite boulders..Teria was knocked over a few times to about 50 degrees heel, so the hatchboards were all put in, allot of wave leaping, crashing into troughs. and another note taken - tie the anchor down or take it below before heavy weather sailing.  Almost reached Radical Bay, but it was barely sheltered from the blast and the boulders to lee had whitewater smashing all over them,, I imagined what could happen in the worst case scenario should the rig break and the engine not start again, so made the decision to give up, turn tail and run for safety.

It took about 5 minutes to run back the distance that had taken about an hour to achieve before.

Once back in Horseshoe Bays shelter, it was time to regroup , sort things out and decide on the next move. One of the things to sort was the roller furling jib somehow got tangled up on it's-self. Either look for spark plugs on the Island and probably spend another day offshore at the Island (and miss work etc) or "have a go". The new plan was to go around the sheltered North West end of the Island and try to go against the roaring wind and seas on the inshore and hopefully less rough channel near the mainland, getting to the mainland again was the aim,,even Cape Palleranda would do, preferably the Strand/duckpond and just maybe Ross River where the trailer was.

The run down the outside of Magnetic Island was fast..for an Investigator. At times Teria surfed waves and got up on the plane, the usual bubbly wake stopped and a surfboard like smooth flow raced astern. At other times Teria broached, suddenly heeled over about 50 degrees and rounded up into a startling u-turn. Luckily the jib was furled away and the main is fully battened so no terrible sail flapping happened. These broaches were cause by "bullets" of wind being speed up by the very steep hills of the Islands coast (the Townsville fairway beacon wind speed was later found to be 25-30knots on the BOM site so these could have been more)

I stayed fairly close to the uninhabited coast first on port tack running,, but round ups meant heading at the rocks-beaches there. So changed tack to starboard so round-ups headed toward safer ocean.

Finally at Rollingstone Bay side there was flat calm and peace at last in the lee of the Island. I took this opportunity to drop the mainsail and lash it to the boom. Then get the motor running again, it was on 1 cylinder so could do about 3-4 knots on flat calm.

Rounded West Point and started getting strong headwinds, but the seas were relatively slight on the inshore side, around 1-2 foot height. Wave energy must be proportional to the cube of the height or something eh? because it was allot easier to go into these waves. Even so, a good one would smash most of the forward momentum out of the hull.  Some small fishing boats were anchored there sheltering, one boat set off with Teria and headed for Cape Palleranda ramp at 3-4 knots with water spraying all over them (they would normally do 20-25knots). Water was also spraying all over and into Teria and me once the shelter was past. Both boat and man were saturated in no time, my jacket a mere token object to this punishment (note- bring the old offshore oilskin next time!)

I checked below, windows were leaking, hatches were leaking, bunks were sodden, even the laminated chart was taking on water! But the motor suddenly fired on both cylinders!! We were racing - into it at 4-5knots then smash! about 2 knots again..build up..smash again. Had to throttle off quickly to get a less damaging speed of about 3 knots.

Hugged the fringing reef of the Island, fortunately it was low tide  and the exposed reef flat reduced most of the wave action to about 1 ft height or less straight from ahead. Good upwind progress at 4 knots into a howling 25-30 knots on the nose. Sub-horizontal spray still driving across the decks into the cockpit area.  Here's a video of Teria battling strong headwinds under power.

Soaked, motoring into strong headwinds

Strong winds - bimini lashed down, decks drenched. With no sails up it was at last possible to take a photo.

Got up towards Picnic Bay before having to leave the reef flats "shelter", this run had allowed most of middle reefs length to be traversed too. The course from there was to clear middle reefs eastern end and navigation pole. The waves were again 2-3 ft height and now at 45 degrees to the bow, not so good for a motor hanging off the transom on a frame. It got wet and sometimes the wind heeled the boat under bare poles so cavitation of the prop happened.. with resulting demonic revs and throttle off.  The motor went back to one cylinder again,, crawling past the reef end at 1 knot barely able to steer, nearly past the windward side of the reef (it was very shallow here 2-3m so anchoring feasible a magnitude less as worrying as the lee shore on the orchid rocks/radical bay side).

Just cleared the reef when the motor died and couldn't be restarted. The strong wind quickly blew Teria down wind a few 100m before I could get the mainsail raised.  She steadied up at 1-2 knots under main, then the jib rolled out and took off at 4-5 knots with rails going under, rounding up etc until i got the trim right and in the groove. Enough windward ground (many km) had been won by motoring up the channel, so could now lay the Strand beach near the rockpool. It was a struggle to sail upwind like that, less sail area would be better, but no choice in that.

As the Strand approached the wave size  began to abate and sailing got easier. A great feeling of having made it to safe shores seeped in as each minute went by. I kept close inshore for tacking up wind, now having the western breakwater to windward to stop the unrelenting wave energy.

Dropped anchor in the duckpond anchorage off the Casino and Marina. Flat safe waters again! Sorted things out, especially got the motor running again and a hot drink into me. Wind chill factor with the constant drenching of the inadequate jacket was starting to take it's toll. About 9 hours of sailing.

About 5pm radioed coast guard that i was on the last leg back to Ross River. The final leg was rough too, but not too far offshore, near other vessels and civilization of the port area.  Motor sailed with furled jib to clear the shipping channel. Also the most unbelievably confused set of seas happened just off the Ports breakwall. Waves were rebounding at about 50-80 degrees to the main seas to cause this. Nearly reached an anchored trawler before tacking onto port tack and sailing again (with idling motor) for the entrance.

On approach i realised that the rudders top pintle fitting was working loose, the nuts and bolts had undone about 15mm and the fitting was flogging around just about to break off - ie loose the rudder and steering on final windward approach to a leeward rockwall entrance. Not good. A quick lashing with some 8mm rope quickly fixed it, it pulled the rudder head towards the traveller and held the loose pintle against the transom and saved the steering system.

Once in and anchored it was a very very slow crawl into the cabin. Got out of the wet gear and into dry clothes plus a hot drink from the thermos allowed  motor function to return. The return upriver all went well but i didn't sign off to coast guard duty until the Teria was actually back on dry land again at the Barnicle st ramp around 8pm. Their radio shift ended at about 5pm but then a phone answering service allows contact after hours to sign off the tripsheet.

Heavy weather and Horseshoe Bay. (trip #12, day 1)

For the midwinters sail i headed off solo from Ross River for an overnight at Horseshoe bay. The weather was about 25C by day 15C by night, 20-25 knot SE and overcast with showers forecast (no strong wind warning issued).

Once rigged tried to sail out of River but couldnt quite point high enough so furled jib and motor sailed. On the way had to stow the bimini and furl it with rope. (lesson, do that before hand in over 20knots)

Set off under full sail but soon the lee rail was under, so took a reef in the main sail. The wind kept increasing so changed down the jib to #2 , it was a bit difficult to operate the halyard shackle (so note taken)

It was a fast close reach on starboard tack , about an hour to be well to windward of Picnic Bay. Kept going into offshore waters and over 2m seas and strong wind with the spray flying. every time a rain shower came the wind increased,,lesson "showers" = "rain squalls" offshore.

 Was a few nm off orchid rocks by nightfall.  A 3/4 moon behind cloud plus city lights glow was enough to see the silhouette of Magnetic Islands hills. Anchored ships way offshore and navigation pole lights of the ship channel , and even the evening star help with direction. (compass still pretty basic and unlit, except by red led headtorch) ,,there were very few shore lights on this part of the coast rather dark there.

Once clear of orchid rock point, Teria was able to run downwind before the seas, which eased things off. I kept the Cape Cleveland lighthouse astern.

Navigation was also backed up by a GPS smart phone in a watertight pouch. The app showed boat position on a google maps satellite image.

To check sail the LED head torch could be switched to white, then back to red for night vision.

Once the lights of Horseshoe Bay appeared it was time to Gybe in. but too hairy for that so rounded up and tacked instead.

Soon was close hauled on port tack in the smooth waters of the bay. The many shore lights and anchor lights on boats helped guide me in. Tacked up a few times to get closer to the anchored boats before dropping the pick about 100m from the breach shorebreak. I was inside a large game fish boat and some big trimarans, good thing about very shoal draft.

Secured the deck, got the anchor light going. "Scamp" the kayak was stowed in the cabin for the rough crossing so pulled it out and stowed on foredeck. The bimini was unfurled but not raised, just used to act a rain dodger while dinner re-heating Thai style pasta spirals on the trangia was underway. Hot milo wasn't too bad either!

It was too rough to take any photos, only a go-pro would've cut it.